Author Topic: 1973 Bonneville Ignition Switch  (Read 2563 times)

Offline ramwing7

  • Advanced Member
  • ***
  • Posts: 40
  • Karma: +0/-0
    • View Profile
1973 Bonneville Ignition Switch
« on: June 02, 2021, 09:48:26 PM »
I recently purchased a 1973 Triumph Bonneville T140V for restoration.
Guy I bought it from said it didn't have an ignition key, which was ok, but on further examination it doesn't have a ignition lock either.  It has the wrong front fork and some other missing pieces, so my question is; If it had an ignition switch, where was it mounted when it left the factory?
Thanks.

Offline L.A.B.

  • Advanced Member
  • ***
  • Posts: 1534
  • Karma: +32/-4
    • View Profile
Re: 1973 Bonneville Ignition Switch
« Reply #1 on: June 02, 2021, 09:59:40 PM »
It has the wrong front fork and some other missing pieces, so my question is; If it had an ignition switch, where was it mounted when it left the factory?

In the left-hand headlamp bracket. The fork being wrong probably explains why it isn't there.
L.A.B.

Offline Rex

  • Advanced Member
  • ***
  • Posts: 1534
  • Karma: +11/-69
  • I love YaBB 1G - SP1!
    • View Profile
Re: 1973 Bonneville Ignition Switch
« Reply #2 on: June 03, 2021, 08:21:27 AM »
So what is the current (hoho) method for starting and stopping the engine, or is the whole loom missing?

Offline ramwing7

  • Advanced Member
  • ***
  • Posts: 40
  • Karma: +0/-0
    • View Profile
Re: 1973 Bonneville Ignition Switch
« Reply #3 on: June 03, 2021, 06:56:26 PM »
Left headlamp bracket?  I don't have one of those, so I guess that explains it.
Not sure how they stopped the poor thing.  Only heard running on starter fluid.  When fluid stopped, engine stopped.   ;D
I suspect I'm gonna have to go the new wiring loom route.  There's some sort of mess there, but it looks like it might be impossible to sort out.
Thanks, folks.

Offline Rex

  • Advanced Member
  • ***
  • Posts: 1534
  • Karma: +11/-69
  • I love YaBB 1G - SP1!
    • View Profile
Re: 1973 Bonneville Ignition Switch
« Reply #4 on: June 03, 2021, 10:04:16 PM »
Yebbut even on starter fluid it still needed a spark, so somewhere the ignition circuit was made before it could run.

Offline oldgoat

  • Advanced Member
  • ***
  • Posts: 3
  • Karma: +0/-0
    • View Profile
    • Email
Re: 1973 Bonneville Ignition Switch
« Reply #5 on: September 08, 2021, 04:56:37 AM »
My '73 T100R Daytona sat for a year while I was involved in other projects. When I got back to it, I could not start the bike, even with a new battery. But I had spark -- the bike would fire on starter fluid but immediately die. Fuel flow into carbs appeared to be fine. I pulled off both carbs, dismantled them, and did a full cleaning, and noted that in both carbs the pilot jet was severely blocked -- took a lot of soaking in carb cleaner, plus running a #10 guitar string into the air pilot screw hole to remove the blockage (I know some advise against the latter, but it was the only way I could clear the blockage, as revealed by free flow of compressed air through the passages). While i had the carbs apart I replaced the needle jets and the float pins. Upon reassembly, I now have first-kick starting every time.