Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - emilios

Pages: [1] 2
1
European and Other Bikes / izh planeta2 charging problem
« on: October 21, 2018, 04:55:04 PM »
Hello guys
im restoring a russian bike for the first time..and probably last also..
I had install a NOS generator and a new regulator..
when the bike start the light for charging turns off which mean the bike is charging..also the headlamp it goes stronger when i rev the bike..
Till here everything looks good..
The problem is that when i check my battery with voltmeter(engine run) i see weird numbers..between 8 and 19 volts but not stable and cant be readen..
It never happens to me this situation..
Anyone had this problem again and can help?
Thanks in advance

2
Japanese Bikes / carb problem?
« on: February 17, 2009, 07:00:31 PM »
Hi I just rebuilt my CB500 four 1972 and start engine..
but something is wrong
If i put air to open position engine start easy but run at very high revs..
if i put air to close position engine start only if i open throttle a lot and when i close throttle engine stop after few seconds..
What do i have to check?
 :-[

3
Japanese Bikes / cb500 four colour ?
« on: November 23, 2008, 07:21:58 PM »
Hi
Im rebuilding a CB500 Four 1971 and i want to paint the candy jade green but i cant find the present code...i know the old one but companies here dont match it..
Can someone help?
Thanks  :'(

4
Japanese Bikes / CB500FOUR
« on: May 10, 2008, 07:46:08 PM »
hi
I just bougth a cb500 1972 and im wondering where to find cheap exsaust 4to4,fuel tank,seat,side covers and handlebar?
I know that http://www.cmsnl.com/ has them all but their expencive..
Can someone help me?
thanks

5
Japanese Bikes / Re: condenser
« on: March 27, 2008, 04:09:46 AM »
Thanks
It help a lot
 :D

6
Japanese Bikes / Re: condenser
« on: March 26, 2008, 07:43:26 PM »
Yes

7
Japanese Bikes / condenser
« on: March 25, 2008, 07:53:04 PM »
What work condenser do for twin engines?

8
British Bikes / Re: bsa m20
« on: March 10, 2009, 07:30:30 PM »
When im going to drive on a hill bike doesnt have power to go...and i put 3rd gear and sometimes 2nd...but still no power....

9
British Bikes / bsa m20
« on: March 09, 2009, 05:58:06 PM »
Hi
I have power problem with my bsa m20 1950(aluminium head)
for a long time....before one year i rebore engine and put +40 piston...for a month or so was ok but after the same trouble with power...
What do i have to check?
I know that M20 is a slow bike but ive been told that has not any problems on hills.....im sure about that...

10
British Bikes / Matchless G3LS problem
« on: November 30, 2008, 06:22:48 PM »
Hi
Its been 2-3 months to start my Matchless G3LS 1955 and today it start first kick :-) but after 3-4 minites i saw some oil getting out where exsaust meet cylinder...
Is that because its been a while to start or i have problem with exsaust valve and quide?
Please advise..
Thanks

11
British Bikes / triumph trw parts?
« on: October 07, 2008, 07:37:27 PM »
Hi guys
Im looking for trw 500 spares....i need pistons and carb parts..
Can someone help me?

12
British Bikes / 21 teeth gearbox
« on: May 09, 2008, 03:43:54 AM »
Hi
My A10 plunger has the standard 19 teeth gearbox sprocket....if i put the 21 teeth sprocket for higher speed will i have gearbox problems?

13
British Bikes / BSA GOLDEN FLASH
« on: April 19, 2008, 02:39:44 AM »
Hi
Can someone tell me the right sprocket for a standard Golden Flash plunger 1952
I'v been told that gearbox is 19 teeth and rear wheel 42 teeth...but what about clutch and crankshaft?

14
British Bikes / Re: chrome or stainless steel?
« on: March 04, 2008, 12:51:24 AM »
Stainless spokes will not rust?
  ???

15
British Bikes / chrome or stainless steel?
« on: March 04, 2008, 12:38:27 AM »
Hi
I will restore my A10
What is better to do?..chrome the old spokes or buy new stainless steel???
Also you will do the best job for chrome and where to find stainless steel spokes?
 ??? ??? ???

Pages: [1] 2